|
12-2-17-snyatie-ustanovka-i-regulirovka-dverejj.html
12.2.17. Removal, installation and adjustment of doorsForward doors
Removal and installation
Door assembled
Details of connection of the lateral repeater of the index of turn
Location of the socket of a plait of electroconducting of a driver's door
Details of installation of door assembly
|
|
- On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
|
- Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.
|
|
- Remove the corresponding lateral repeater the turn index (E22/1 or E22/2) and disunite the socket of its electroconducting (1).
- Uncover at the left or on the right (depending on what of doors will act in film) under the dashboard (see. Section Removal and installation of the bottom covers of the dashboard).
- Separate a carpet (2) from a rack And in a forward foot well.
-
On a rack And in the corresponding foot well disunite the socket of door electroconducting (X35/41 or X35/42).
- Take the corresponding contact elements from leveling potential of grounding of a connecting block (3).
- On a rack And in a foot well remove a wire of grounding of the lateral repeater of the index of turn.
- Liberate a rubber sleeve through passage (4) of door assembly and from a rack And, - the damaged sleeve is subject to replacement.
- Liberate from a rack And a plait of door electroconducting, - try to remember a route of laying of a plait.
- Prop up a door and turn out screws of fastening bottom (5) and the top (6) loops.
- Remove a door.
- Installation is made upside-down, - do not forget to adjust a door (see below).
- On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
- In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).
|
|
Door in the disassembled condition
|
|
Details of connection of a door rear-view mirror
|
|
|
Location of internal sockets (2) of door electroconducting |
|
|
Rubber sleeve through passage (3) door electroconductings |
|
|
- Execute procedures 1 and 2 (see above).
- Remove the panel of an internal upholstery of a door (see. Section Removal and installation of an internal upholstery of door assemblies).
- Disconnect electroconducting from a door loudspeaker.
- Remove the module of management of a door (see. Head Onboard electric equipment).
- Accurately remove a film insulating cover of a door, - in case of damage identification the film should be replaced in order to avoid hit in moisture salon.
- Disunite the socket (1) electroconducting of a door rear-view mirror.
- Liberate from clamps and disunite sockets (2) of door electroconducting, - try to remember a route of laying of a plait.
- Liberate a rubber sleeve through passage (3) of door assembly and from a rack And, - the damaged sleeve is subject to replacement.
- Liberate an electroconducting plait from door assembly.
- Prop up a door and turn out screws of fastening bottom (5) and the top (4) loops.
- Remove a door.
- Installation is made upside-down, - do not forget to adjust a door (see below).
- On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
- In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).
|
|
Adjustment
Adjustment of door assembly
|
|
- Release screws of fastening bottom (1) and the top (2) loops. Also weaken screws of fastening of a locking wedge (3).
-
Correct the provision of a door in a body aperture, achieving, that the gap was identical on all perimeter, and the door surface in a closed position of the last appeared aflush with a surface of surrounding body elements, - in case of need enclose under loops adjusting laying, or take those.
- Having achieved demanded result, tighten screws of fastening of loops (4 and 5) and a locking wedge (3).
- Grease the mechanism of the lock and make sure of smoothness of closing of a door.
- In summary tint heads of screws.
|
|
Back doors
Removal and installation
Details of installation of a back door
The order of performance of procedure is similar described above for forward doors except for the actions interfaced to a detachment of electroconducting of door mirrors and repeaters of indexes of turns. Adjustment
The order of performance of adjustment of back doors is completely similar described above for lobbies. Door of a back (Versatile person model)
Removal and installation
Details of installation of a door of a back on the Versatile person models
|
|
Details of connection of electroconducting of a door of a back on the Versatile person models
|
|
|
Removal of a protector (4) left edges of a doorway of a back on the Versatile person models |
|
|
Removal of the panel of furnish of the left back rack |
|
|
Location of a tube (5) electroconductings through passage and screws (7) of fastening of the top loop of a door of a back on the Versatile person models |
|
|
Location of the limiter (6) of opening and screws (8) fastenings of the bottom loop of a door of a back on the Versatile person models |
|
|
- Execute procedures of paragraphs 1 and 2 of subsection
Forward doors.
- Remove a spare wheel.
- On models of the corresponding complete set (V53 and V57 codes) uncover a luggage compartment (And).
- On models of the corresponding complete set (V53 code) uncover (In) a lateral ware compartment, then turn out the fixing screw (D) and separate a ware compartment (C) from a back rack.
- Remove from a back rack a protector (4) left edges of a doorway.
- Remove the panel (Е) of furnish of the left back rack.
- Release a clamp (1) plait of door electroconducting.
- Release a returnable spring (2).
- Turn out fixture of fastening of a tube (5) electroconductings through passage.
- Remove the panel of an internal upholstery of a door (see. Section Removal and installation of an internal upholstery of door assemblies).
- Disunite the socket of electroconducting of the electromotor of a drive of a back screen wiper, - mark wires, try to remember a route of laying of a plait.
- Disunite the socket of electroconducting of an element of heating of back glass, - mark wires, try to remember a route of laying of a plait.
- Liberate electroconducting from door assembly.
- Release fixture and disconnect from a door the limiter of a course of its opening (6).
- Holding a door, turn out screws of fastening it top (7) and bottom (8) loops.
- Remove a door.
- Installation is made upside-down, - do not forget to adjust a door (see below).
- On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
- In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).
|
|
Adjustment
|
|
Adjustment of a door of a back on the Versatile person models (1 of 5)
|
|
|
Adjustment of a door of a back on the Versatile person models (2 of 5)
|
|
|
Adjustment of a door of a back on the Versatile person models (3 of 5)
|
|
|
Adjustment of a door of a back on the Versatile person models (4 of 5)
|
|
|
Adjustment of a door of a back on the Versatile person models (5 of 5)
|
|
|
- Remove from a back door a sharovy finger (1).
- Remove from a back door the lock (2) drummer.
- Remove from a body element a latch (3).
- On models 463.246/250 execute procedures
of paragraphs 6 and 7
, and also uncover the storage battery.
- Remove an internal upholstery of a door of a back (see. Section Removal and installation of an internal upholstery of door assemblies).
- Having released fixture, adjust the provision of a door in a body aperture according to the same criteria that take place for lateral doors (see
paragraph 2). Also adjust position of the drummer (6) by a podstukivaniye it a hammer at the released fixture.
- Installation of components is made as it should be the return to an order of their dismantle, - do not forget to adjust as appropriate position of the drummer (2) and latches (3).
|
|
Folding board (Cabriolet models)
Removal and installation
Details of installation of a folding board on the Cabriolet models (1 of 3)
Details of installation of a folding board on the Cabriolet models (2 of 3)
Details of installation of a folding board on the Cabriolet models (3 of 3)
|
|
- Develop aside the holder of a spare wheel.
- Open a folding board (2).
- Open a cover (5), release clamps and take the loose leaf (6) tool compartments.
- Disunite the socket (M14/7x1) of the electromotor of the activator of the uniform lock.
- By means of a steel wire or a narrow screw-driver remove from the socket terminals (7).
- At the left in a frame of a folding board disconnect the terminal (8) from the socket (9) of the contact sensor switch, - again use a wire or a narrow screw-driver, previously having removed a plastic protective cap (10) and unblock a clamp.
- Liberate from a board (2) both plaits of electroconducting (11).
- Close a cover (5) tool compartments.
- Turn out screws (1) fastening of limiters of a course of opening of a board, - screws are subject to replacement without fail.
- Close a board, - try not to jam electroconducting (11).
- Turn out loopy screws (3), then open a board (2) and remove it from the car, - use the help of the assistant.
- Installation is made upside-down, - for the purpose of simplification of filling of electroconducting grease plugs through passage with soap solution.
- In summary make board adjustment (see below)
|
|
Adjustment
Adjustment of a folding board (1 of 3)
Adjustment of a folding board (2 of 3)
Adjustment of a folding board (3 of 3)
|
|
- Release the holder (1) arm запаски and remove it from a spherical head (2).
- Weaken loopy bolts (3).
- Cast away a board and weaken screws of a locking wedge (4).
- Tighten bolts (3) and (4) so that there was a possibility of correction of provision of components fixed by them a podstukivaniye way a hammer.
- Close a board and make sure of similarity of gaps (And, In and C) its landings in a body aperture. Also be convinced that the upper edge of a board (and Е) is closed by D aflush with surrounding body panels.
- In case of need correct landing of loops and a locking wedge.
- In summary do not forget to tighten fixing bolts.
|
|
|
|