Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
9.1. A full drive - the general information
9.2. Transfer case
9.3. Bridges
9.3.1. General information
9.3.2. Check and adjustment oil level / replacement in assemblies of bridges
9.3.3. Check of stuffing by greasing of sharnirny casings of rotary assemblies of the forward bridge
9.3.4. Adjustment of wheel bearings of a forward axis
9.3.5. Check of concentricity of landing of connecting flanges of leading gear wheels of the main transfers
9.3.6. Replacement of epiploons of leading gear wheels of the main transfers
9.3.7. Removal and installation of leading gear wheels of the main transfers
9.3.8. Removal, installation and adjustment of executive cylinders and components of the mechanism of a drive of blocking of interwheel differentials
9.3.9. Dismantling and assembly of the executive cylinder of a drive of blocking of differential
9.3.10. Removal and installation of naves of forward wheels
9.3.11. Dismantling and assembly of naves of forward wheels
9.3.12. Removal and installation of power shafts of the forward bridge
9.3.13. Adjustment of bearings of rotary knots
9.3.14. Dismantling and assembly of a sharnirny casing of the forward bridge
9.3.15. Dismantling and assembly of a power shaft
9.3.16. Removal and installation of semi-axes
9.3.17. Dismantling and semi-axis assembly
9.3.18. Removal and installation of assemblies of interwheel differentials with conducted gear wheels of the main transfers
9.3.19. Dismantling and assembly of interwheel differentials
9.3.20. Check of correctness of gearing of gear wheels of the main transfer
9.3.21. Removal and installation of assemblies of the forward and back bridge
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 


9-3-6-zamena-salnikov-vedushhikh-shesteren-glavnykh-peredach.html

9.3.6. Replacement of epiploons of leading gear wheels of the main transfers

Details of installation of sealing elements of a leading gear wheel of the main transfer

1 — the Adjusting washer
2 — the Ring
3 — Maslootrazhatel
4 — Kompressionnoye a ring
5 — the Sealing ring

6 — the Internal epiploon
7 — the External epiploon
8 — the Nut
9 — the Connecting flange

 PERFORMANCE ORDER

  1. Remove a connecting flange (see. Section Check of concentricity of landing of connecting flanges of leading gear wheels of the main transfers).
  2. Remove internal (6) and external (7) epiploons.
  3. Remove a sealing ring (5).
  4. Having slightly greased with liquid oil, establish a new ring (5).
  5. By means of a special opravka (460 589 15 15 00) plant on the regular places new epiploons (6 and 7).

Rings without an obrezinenny external edge are put on hermetic. The epiploon (6) is established with filling of a disk of an opravka, (7) - without disk filling.

  1. Fill space between a boot and sealing sponges of an external epiploon (7) light greasing. With the same greasing slightly grease sealing sponges and a spring dilator.
  2. Establish into place a connecting flange (see. Section Check of concentricity of landing of connecting flanges of leading gear wheels of the main transfers).

«previous page
9.3.5. Check of concentricity of landing of connecting flanges of leading gear wheels of the main transfers		 following page»
9.3.7. Removal and installation of leading gear wheels of the main transfers