Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
9.1. A full drive - the general information
9.2. Transfer case
9.3. Bridges
9.3.1. General information
9.3.2. Check and adjustment oil level / replacement in assemblies of bridges
9.3.3. Check of stuffing by greasing of sharnirny casings of rotary assemblies of the forward bridge
9.3.4. Adjustment of wheel bearings of a forward axis
9.3.5. Check of concentricity of landing of connecting flanges of leading gear wheels of the main transfers
9.3.6. Replacement of epiploons of leading gear wheels of the main transfers
9.3.7. Removal and installation of leading gear wheels of the main transfers
9.3.8. Removal, installation and adjustment of executive cylinders and components of the mechanism of a drive of blocking of interwheel differentials
9.3.9. Dismantling and assembly of the executive cylinder of a drive of blocking of differential
9.3.10. Removal and installation of naves of forward wheels
9.3.11. Dismantling and assembly of naves of forward wheels
9.3.12. Removal and installation of power shafts of the forward bridge
9.3.13. Adjustment of bearings of rotary knots
9.3.14. Dismantling and assembly of a sharnirny casing of the forward bridge
9.3.15. Dismantling and assembly of a power shaft
9.3.16. Removal and installation of semi-axes
9.3.17. Dismantling and semi-axis assembly
9.3.18. Removal and installation of assemblies of interwheel differentials with conducted gear wheels of the main transfers
9.3.19. Dismantling and assembly of interwheel differentials
9.3.20. Check of correctness of gearing of gear wheels of the main transfer
9.3.21. Removal and installation of assemblies of the forward and back bridge
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 


9-3-16-snyatie-i-ustanovka-poluosejj.html

9.3.16. Removal and installation of semi-axes

Details of installation of a back semi-axis

1 — the ABS Sensor
2 — Fixing screws
3 — a bearing Cover

4 — Poluos
5 — the Sleeve of a case of the back bridge

 PERFORMANCE ORDER

  1. Remove boots of the parking brake (see. Head Brake and auxiliary systems).
  2. Remove from a bearing (3) cover the wheel ABS (1) sensor.
  3. Turn out bolts (2) fastenings of a cover (3) to a sleeve of a case of the back bridge (5).
  4. At removal of the left semi-axis dismantle the executive cylinder of a drive of blocking of differential (see. Section Removal, installation and adjustment of executive cylinders and components of the mechanism of a drive of blocking of interwheel differentials).
  5. Take a semi-axis (4), - try not to damage a rotor of the wheel sensor.
  6. Examine the removed semi-axis on existence of signs of damages, in case of need prepare I will close.
  7. Installation is made upside-down, - track, that before semi-axis installation on a basic disk the sealing ring was established.

«previous page
9.3.15. Dismantling and assembly of a power shaft		 following page»
9.3.17. Dismantling and semi-axis assembly







QX4.ONLINE
S40.ONLINE
A-8.ONLINE
W124.ONLINE
RX300.ONLINE
W140.ONLINE
B3-B4.SPACE
B3B4.SPACE
A-8.SPACE