Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
3.1. Specifications
3.2. Active system of the prevention of term of approach planned THAT (ASSYST)
3.3. Schedule of routine maintenance
3.4. General information on settings
3.5. Check of levels of liquids, control of leaks
3.6. Check of a condition of tires and pressure in them, designation of tires and disks of wheels, rotation of wheels
3.7. Replacement of impellent oil and oil filter
3.8. Check of brake system
3.9. Power supply system check, replacement of the fuel filter
3.10. Check of a condition and replacement of hoses of an impellent compartment, localization of leaks
3.11. Check of a condition of multicostal belts of a drive of auxiliary units
3.12. Check of functioning of system of cooling and frost resistance of cooling liquid, liquid replacement
3.13. Check of a condition of system of production of the fulfilled gases
3.14. ATF and AT filter replacement
3.15. Visual check of tightness of automatic transmission
3.16. Check of a condition of components of a suspension bracket and steering
3.17. Check of a condition of boots of power shafts
3.18. Check of central air of air
3.19. Greasing of limiters of doors and cylinders of locks
3.20. Visual control of seat belts and modules of safety cushions
3.21. Check of operability of headlights and horn
3.22. Check of a condition and replacement of brushes of screen wipers
3.23. Check of a condition of the battery, care of it and charging
3.24. Replacement of the salonny filter
3.25. Replacement of liquid of a drive of blocking of differential
3.26. Replacement of brake liquid
3.27. Check and replacement of spark plugs, check of a condition of high-voltage wires (petrol models)
3.28. Replacement of candles of an incandescence (diesel models)
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 









3-13-proverka-sostoyaniya-sistemy-vypuska-otrabotavshikh-gazov.html

3.13. Check of a condition of system of production of the fulfilled gases

 PERFORMANCE ORDER

  1. Check should be made at the cold engine therefore it is better to be engaged in it before the first trip for the present day or not earlier than in three hours after engine switching off. Check a condition twist release systems, beginning from the engine and finishing a cut of an exhaust pipe. In an ideal this check should be carried out at the car lifted on the winch when from below to it there is a free access. If the winch is inaccessible, поддомкратьте the car and reliably establish it on support.
  1. Examine pipes and trumpet connections on existence of signs of development of leaks, strong corrosion and mechanical damages. Check a condition and reliability of fastening of all brackets and подвесов systems.

Podvesa, located near the catalytic converter usually are made of heat resisting rubber and differ red color.

  1. At the same time examine the car bottom on existence of holes, the corrosion, the dispersed seams and the other defects allowing penetration of fulfilled gases in salon of the car. Close up all openings suitable hermetic.
  2. The release system, often is a source of a roar and other unpleasant sounds. Shake and pull pipes, exhaust silencers and the catalytic converter. If any of components adjoin to elements of a body or suspension bracket details, replace fixture of system of release. In more detail the design of system of production of the fulfilled gases is considered in Head of the Power supply system and production of the fulfilled gases.
  3. Examine the electroconducting brought to a lambda probe. In case of need replace established on a reception pipe a lambda probe.
  4. Survey of an internal surface of an exhaust pipe allows to define the current working state of the engine. The structure of deposits in a pipe speaks about quality of settings of the engine. If the pipe from within black and smoked, it can indicate that it is necessary to check fuel system carefully.


«previous page
3.12. Check of functioning of system of cooling and frost resistance of cooling liquid, liquid replacement
following page»
3.14. ATF and AT filter replacement