Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
11.1. Specifications
11.2. Forward suspension bracket
11.3. Back suspension bracket
11.4. Steering
11.4.1. General information
11.4.2. Check of a pressure of the steering pump
11.4.3. Check and adjustment of the hydraulic limiter
11.4.4. Adjustment of a steering shaft
11.4.5. Assessment of a condition of components of a steering drive
11.4.6. Removal and installation of a steering wheel
11.4.7. Removal and installation of a contact cable drum of a steering wheel
11.4.8. Removal and installation of the sensor of an angle of rotation of a steering wheel
11.4.9. Removal and installation of the mechanism of an electronic blokirator of a steering column
11.4.10. Removal and installation of a steering column with the adjustment electric drive
11.4.11. Removal and installation of the steering pump
11.4.12. Removal and installation of the line of cooling of GUR liquid
11.4.13. Removal and installation of the steering mechanism
11.4.14. Design of the steering mechanism
11.5. Suspension bracket geometry
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 









11-4-13-snyatie-i-ustanovka-rulevogo-mekhanizma.html

11.4.13. Removal and installation of the steering mechanism

Petrol models

The corresponding illustrative material is presented on an illustration the Scheme of the organization of a steering drive and an illustration is lower, which all references meeting in the text concern.

Details of installation of the steering mechanism on petrol models

6 — the Steering soshka
8 — the Steering mechanism
15 — Hollow bolts of shtutserny connections

16 — the Bolt of fastening of a steering shaft
17 — Bolts of fastening of assembly of the steering mechanism

 PERFORMANCE ORDER

  1. By means of a suitable stripper выпрессуйте cross-section draft (9) from a steering soshka (7).
  2. On the models equipped with engines of a series 113 remove the left block headlight (see. Head Onboard electric equipment) and the steering pump (see. Section Removal and installation of the steering pump).
  3. Remove a radiator (see. Head of System of cooling, heating, ventilation and air conditioning).
  4. Remove the line (14) of cooling of GUR liquid (see. Section Removal and installation of the line of cooling of GUR liquid).
  5. Turn out hollow bolts (15) shtutserny connections and disconnect from assembly of the steering mechanism hydraulic lines, - merge hydraulic liquid in in advance prepared capacity.
  6. Turn out a bolt (16) and disconnect the bottom kardanny hinge of a steering shaft from an entrance shaft of the steering mechanism.
  7. Turn out fixing bolts (17) and remove assembly of the steering mechanism.
  8. Installation is made upside-down. Do not forget to check levels of working liquids and, in case of need to make the corresponding adjustments.
  9. In summary make cleaning of memory of the processor of system of onboard self-diagnostics (see. The head of System of electric equipment of the engine) also adjust corners of installation of forward wheels (see. Part suspension bracket Geometry).

Diesel models

Models 463.323 (М612)

The corresponding illustrative material is presented on an illustration the Scheme of the organization of a steering drive and an illustration is lower, which all references meeting in the text concern.

Preparation for removal of the steering pump (model 463.323)

13 — the Pressure head line
15 — the Left air line
16 — the Right air line
17 — the Belt of a drive of auxiliary units

18 — the Driving pulley
19 — the To/in Compressor
20 — the Fixing collar

 PERFORMANCE ORDER

  1. Remove panels of furnish of a cover of a head of cylinders.
  2. Remove the vyazkostny coupling of a drive of the fan of system of cooling (see. Head of System of cooling, heating, ventilation and air conditioning).
  3. Remove a radiator of system of cooling (see. Head of System of cooling, heating, ventilation and air conditioning).
  4. Remove left (15) and the right (16) sleeves of inlet air lines.
  5. Remove a belt of a drive of auxiliary units (see. Head Engine).
  6. Remove a pulley (18) drives of the steering pump (11) (see. Section Removal and installation of the steering pump).
  7. Pump out liquid from the GUR tank.
  8. Remove the To/in compressor (19) and, without disconnecting refrigerator lines, take him aside.
  9. Remove the left forward wheel.
  10. Remove the left block headlight (see. Head Onboard electric equipment).
  11. By means of a suitable stripper выпрессуйте cross-section draft (9) from a steering soshka (7).
  12. Having executed the procedures described in paragraphs from 5 to 7 for petrol engines, remove assembly of the steering mechanism (8).
  13. Installation is made upside-down. In summary do not forget to make adjustment of corners of installation of forward wheels (see. Part suspension bracket Geometry).

Models 463.333 (М628)

The corresponding illustrative material is presented on illustrations of the Detail of installation of the steering pump (model with M628 engines) (1 of 2), Details of installation of the steering pump (with M628 engines) (2 of 2) and an illustration are lower than model, which all references meeting in the text concern.

Location of a cover (22) in a wheel arch


 PERFORMANCE ORDER

  1. To Poddomkratta the car also establish it on props.
  2. Remove the left forward wheel.
  3. Remove a loker of protection of a wheel arch.
  4. Remove the left block headlight (see. Head Onboard electric equipment).
  5. Remove an air purifier (1).
  6. Remove the left air inlet (2).
  7. Turn out four screws, take measuring щуп and unscrew a cover of a maslonalivny mouth, then remove the finishing panel (4).
  8. Remove a radiator (see. Head of System of cooling, heating, ventilation and air conditioning).
  9. Remove a casing of the oil filter (20).
  10. Pump out liquid from the GUR (7) tank.
  11. Remove the tank (7) (see paragraphs 13 and 14 in the Section Removal and installation of the steering pump).
  12. Throw off a belt of a drive of auxiliary units (14) from a driving pulley (10) pump assemblies (11) (see paragraph 15 in the Section Removal and installation of the steering pump).
  13. Weaken fastening of an air line (21) on a head of cylinders.
  14. Uncover (22) in a wheel arch.
  15. Remove the turbokompressor thermofilter.
  16. Remove the left bottom air line (17).
  17. By means of a suitable stripper выпрессуйте cross-section draft from a steering soshka.
  18. Having executed the procedures described in paragraphs from 5 to 7 for petrol engines , remove assembly of the steering mechanism (8).
  19. Installation is made upside-down. Do not forget to check levels of working liquids and, in case of need to make the corresponding adjustments.
  20. In summary make cleaning of memory of the processor of system of onboard self-diagnostics (see. The head of System of electric equipment of the engine) also adjust corners of installation of forward wheels (see. Part suspension bracket Geometry).


«previous page
11.4.12. Removal and installation of the line of cooling of GUR liquid
following page»
11.4.14. Design of the steering mechanism