Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
11.1. Specifications
11.2. Forward suspension bracket
11.3. Back suspension bracket
11.4. Steering
11.4.1. General information
11.4.2. Check of a pressure of the steering pump
11.4.3. Check and adjustment of the hydraulic limiter
11.4.4. Adjustment of a steering shaft
11.4.5. Assessment of a condition of components of a steering drive
11.4.6. Removal and installation of a steering wheel
11.4.7. Removal and installation of a contact cable drum of a steering wheel
11.4.8. Removal and installation of the sensor of an angle of rotation of a steering wheel
11.4.9. Removal and installation of the mechanism of an electronic blokirator of a steering column
11.4.10. Removal and installation of a steering column with the adjustment electric drive
11.4.11. Removal and installation of the steering pump
11.4.12. Removal and installation of the line of cooling of GUR liquid
11.4.13. Removal and installation of the steering mechanism
11.4.14. Design of the steering mechanism
11.5. Suspension bracket geometry
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 







11-4-7-snyatie-i-ustanovka-kontaktnogo-kabelnogo-barabana-rulevogo-kolesa.html

11.4.7. Removal and installation of a contact cable drum of a steering wheel

Details of installation of a contact cable drum on release models for 30.06.02.

32h — Fixing bolts
А54 — the Cable drum

B24/8 — the Sensor of an angle of rotation of a steering wheel

Details of installation of a contact cable drum on release models since 01.07.02.

1 — Contact plugs
32h — Fixing bolts

А54 — the Contact drum

 PERFORMANCE ORDER

  1. Develop a steering wheel in rectilinear situation.
  2. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding

  1. Remove a steering wheel (see. Section Removal and installation of a steering wheel).
  2. Turn out fixing bolts (32h) so that there was a possibility of removal of a contact cable drum (А45), - bolts also carry out a role directing, providing unambiguity of interface of components at assembly.
  3. Accurately remove a drum (А45) from a casing of a steering column.
  4. Examine the removed drum on existence of mechanical defects, in case of need prepare replaceable assembly.
  5. Installation is made upside-down, - track completeness and correctness of landing of a drum, on release models from 01.07.02 try not to damage contact plugs (1).
  1. Before installation of a steering wheel make centering of a cable drum (А45) for what, having completely screwed fixing screws (32h), develop a drum counter-clockwise before emergence of notable resistance, then return it back on 3-3.5 turns so that bolts (32h) could be turned again off through specially provided apertures.

The cable drum can be scrolled as much as possible on 6-7 turns.

  1. At the corresponding complete set деактивируйте service mode of TELE AID system.
  2. In summary make cleaning of memory of the processor of system of onboard self-diagnostics (see. Head of System of electric equipment of the engine).


«previous page
11.4.6. Removal and installation of a steering wheel
following page»
11.4.8. Removal and installation of the sensor of an angle of rotation of a steering wheel