Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
5.1. System of cooling of the engine
5.2. Systems of ventilation, heating and air conditioning
5.2.1. General information and security measures
5.2.2. Removal and control panel installation by functioning of systems of heating / ventilation / air conditioning
5.2.3. Removal and installation of the salonny filter
5.2.4. Removal and installation of the fan of the heater / conditioner of air and its module of management
5.2.5. Removal and installation of the heat exchanger of a heater
5.2.6. Removal and installation of the circulating pump of a heater
5.2.7. Removal and installation of back ventilating guards
5.2.8. Check of level of a coolant in a working path of To/in system
5.2.9. Removal and installation of sensors of To/in system
5.2.10. Removal and installation of auxiliary ventilyatorny assembly
5.2.11. Removal and installation of the electromotor of a drive of a ventilating zaslonka
5.2.12. Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation
5.2.13. Removal and installation of the electromotor of a drive of a mixing zaslonka
5.2.14. Removal and installation of the evaporator of To/in system and its casing
5.2.15. Removal and installation of the compressor of To/in system
5.2.16. Removal and installation of the condenser of To/in system
5.2.17. Removal and installation of the broad valve
5.2.18. Removal and receiver dehumidifier installation
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 







5-2-16-snyatie-i-ustanovka-kondensatora-sistemy-k-v.html

5.2.16. Removal and installation of the condenser of To/in system

All sealing elements are subject to replacement without fail!

Petrol models

Details of installation of the To/in condenser on petrol models (with the H02 code)

1 — the Refrigerator line to a receiver dehumidifier
2 — the Refrigerator line to the condenser

3 — the Condenser

 PERFORMANCE ORDER

  1. Remove auxiliary ventilyatorny assembly (see. Section Removal and installation of auxiliary ventilyatorny assembly).
  2. In the conditions of specialized HUNDRED make the К/В system discharge.
  3. Disconnect refrigerator lines from a receiver dehumidifier (1) and the condenser (2), - prepare replaceable sealing rings.
  4. Having pulled in specified in a picture an arrow the direction, remove the condenser (3), - try not to damage heat exchanger plates.
  5. Installation is made upside-down.
  6. In summary start the engine on single turns and approximately for 4 minutes turn on the conditioner on the maximum hladoproizvoditelnost, - the air temperature, submitted to salon via deflectors of the central air line of the dashboard, should not fall below value +5°С.
  7. Make sure of lack of signs of development of leaks from the To/in system path, check serviceability of functioning of system.

Diesel models

Details of installation of the To/in condenser on diesel models (М628)

1 — the Radiator of system of cooling
2 — the Condenser
3, 4 — Lines of an okhladitelny path
5, 6 — the ATF Lines

7, 8 — Refrigerator lines
9 — Clamps
10 — Bolts
11 — Elements of fastening of the condenser

 PERFORMANCE ORDER

  1. The condenser (2) acts in film assembled with a radiator of system of cooling (1), - see. Section Removal and installation of a radiator of system of cooling.
  2. In case of need turn out bolts (10) and, having pulled in specified in a picture an arrow the direction, liberate the condenser (2) of fixing elements (11), - try not to damage plates of heat exchangers.
  3. Installation is made upside-down.
  4. In summary check paths of systems of cooling and air conditioning on existence of signs of development of leaks, make sure of serviceability of functioning К/В.


«previous page
5.2.15. Removal and installation of the compressor of To/in system
following page»
5.2.17. Removal and installation of the broad valve