Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
5.1. System of cooling of the engine
5.2. Systems of ventilation, heating and air conditioning
5.2.1. General information and security measures
5.2.2. Removal and control panel installation by functioning of systems of heating / ventilation / air conditioning
5.2.3. Removal and installation of the salonny filter
5.2.4. Removal and installation of the fan of the heater / conditioner of air and its module of management
5.2.5. Removal and installation of the heat exchanger of a heater
5.2.6. Removal and installation of the circulating pump of a heater
5.2.7. Removal and installation of back ventilating guards
5.2.8. Check of level of a coolant in a working path of To/in system
5.2.9. Removal and installation of sensors of To/in system
5.2.10. Removal and installation of auxiliary ventilyatorny assembly
5.2.11. Removal and installation of the electromotor of a drive of a ventilating zaslonka
5.2.12. Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation
5.2.13. Removal and installation of the electromotor of a drive of a mixing zaslonka
5.2.14. Removal and installation of the evaporator of To/in system and its casing
5.2.15. Removal and installation of the compressor of To/in system
5.2.16. Removal and installation of the condenser of To/in system
5.2.17. Removal and installation of the broad valve
5.2.18. Removal and receiver dehumidifier installation
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 







5-2-12-snyatie-i-ustanovka-shagovogo-ehlektromotora-privoda-zaslonki-pereklyucheniya.html

5.2.12. Removal and installation of the step-by-step electromotor of a drive of a zaslonka of switching of modes of air circulation

Details of installation of the step-by-step electromotor (Sq.m/5) of a drive of a zaslonka of switching of modes of air circulation

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove a ware box (see. Head Body).
  4. Turn out three fixing screws (1) (a TORX type head), disunite the socket (3) electroconductings and remove the electromotor (Sq.m/5) of a drive of a zaslonka of switching of modes of circulation from an evaporator casing.
  5. Installation is made upside-down. On models of the corresponding complete set do not forget деактивировать a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  6. In summary it is necessary to make normalization of the electromotor (Sq.m/6) of the left mixing zaslonka with use of the STAR DIAGNOSIS input reader, - address for the help on HUNDRED Mercedes-Benzs.
  7. Do not forget to make also cleaning of memory of the processor of system of onboard self-diagnostics (see. Head of System of electric equipment of the engine).
  8. Make sure of serviceability of functioning of К/В system.


«previous page
5.2.11. Removal and installation of the electromotor of a drive of a ventilating zaslonka
following page»
5.2.13. Removal and installation of the electromotor of a drive of a mixing zaslonka