Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
10.1. Specifications
10.2. Check of brake system on leaks
10.3. Check of serviceability of functioning of the vacuum amplifier of brakes
10.4. Removal and installation of the tank of brake liquid and main brake cylinder (GTTs)
10.5. Removal and installation of the vacuum amplifier of brakes and sensor of a course of a diaphragm of BAS
10.6. Removal and installation of the vacuum pump (diesel engines)
10.7. Removal and installation of modules of management of ABS/EBV/ESP
10.8. Removal and ABS/4-ETS hydromodulator installation
10.9. Removal and installation of wheel ABS sensors
10.10. Removal and installation of rotors of wheel ABS sensors
10.11. Removal and installation of a pedal of a foot brake
10.12. Removal and installation of the lever of raising of the parking brake with a bearing bracket
10.13. Replacement of brake hoses
10.14. Check of a condition and replacement of brake shoes
10.15. Replacement of boots of the parking brake
10.16. Removal and installation of supports of brake mechanisms
10.17. Repair of a support of the fixed type
10.18. Check, removal and installation of brake disks
10.19. Removal and installation of components of a hummock drive of the parking brake
10.20. Adjustment of a drive of the parking brake
10.21. Pumping of brake system
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 







10-9-snyatie-i-ustanovka-kolesnykh-datchikov-abs.html

10.9. Removal and installation of wheel ABS sensors

Forward sensors

Details of installation of the forward wheel ABS sensor

L6/1 — the Sensor of the left forward wheel
L6/2 — the Sensor of the right forward wheel

1 — the Bolt

 PERFORMANCE ORDER

  1. Remove the corresponding forward wheel.
  2. Turn out a fixing bolt (1) and remove the sensor (L6/1 or L6/2).
  3. Slightly grease its landing nest in stupichny assembly, then disconnect from the sensor electroconducting (X62/26 or X62/27).
  4. Estimate a rotor condition (a measuring ring) on stupichny assembly, in case of need make replacement (see. Section Removal and installation of rotors of wheel ABS sensors).
  5. Installation is made upside-down.

Back sensors

Scheme of an arrangement of electroconducting of the wheel sensor

3 — the Tool box in a luggage compartment
4 — Burn down electroconductings

X92/3 — I Will corrode ABS electroconductings

Details of installation of the back wheel ABS sensor

1 — the Plug in stupichny assembly
2 — the Brass coupling

L6/3 — the Wheel sensor

Location of an opening through passage (5) in the floor panel


 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding
  1. Remove the corresponding back wheel.
  2. Carefully liberate the sensor (L6/3 or L6/4) from the brass landing plug (1).
  3. Estimate a rotor condition (a measuring ring) on a nave, - in case of need make replacement (see. Section Removal and installation of rotors of wheel ABS sensors).
  4. Remove the brass coupling (2).
  5. Remove the assembly block of the relay in an impellent compartment of the car (see. Head Onboard electric equipment).
  6. Disunite the socket (X92/3) of electroconducting of ABS laid in a tool box (3) in a luggage compartment of the car.
  7. Disunite other sockets of a plait (4) in a tool box (3).
  8. Remove the vlagozashchitny screen.
  9. Push a plait of electroconducting (4) in an opening through passage (5) in the floor panel.
  10. Disconnect from the socket (X92/3) electroconducting of the wheel sensor (L6/3 or L6/4) and finally remove the last assembled with a plait.
  11. Installation is made upside-down, - track correctness of laying of electroconducting, for fixing of a plait use a new insulating tape.
  12. On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  13. 2 in summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).


«previous page
10.8. Removal and ABS/4-ETS hydromodulator installation
following page»
10.10. Removal and installation of rotors of wheel ABS sensors