Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
9.1. A full drive - the general information
9.2. Transfer case
9.2.1. Oil replacement in a transfer case
9.2.2. Removal and installation of the module of management of a transfer case
9.2.3. Removal and installation of a vacuum receiver of a control system by blocking of differentials
9.2.4. Removal and installation of the vacuum pump of a drive of blocking of differentials
9.2.5. Removal and installation of the servomotor of a transfer case
9.2.6. A detachment and connection of driveshafts on a transfer case
9.2.7. Removal and installation of a transfer case
9.2.8. Removal and installation of support of a suspension bracket of a transfer case
9.2.9. Design of a transfer case
9.2.10. Replacement of epiploons
9.2.11. Removal and installation of the executive cylinder of a drive of blocking of interaxal differential
9.2.12. Removal and installation of a forward cover
9.2.13. Removal and installation of a cover of the bearing of an intermediate flange
9.2.14. Dismantling and assembly of a cover of the bearing
9.2.15. Removal and installation of a cover of an intermediate flange
9.2.16. Removal and installation of an intermediate flange
9.2.17. Removal and installation of interaxal differential
9.2.18. Dismantling and assembly of interaxal differential
9.2.19. Removal and installation of entrance and intermediate shaft
9.2.20. Dismantling entrance (leading shaft)
9.2.21. Dismantling of an intermediate shaft
9.2.22. Removal and installation of components of the mechanism of inclusion of blocking of interaxal differential
9.2.23. Removal and installation of components of the mechanism of switching of modes of a transfer case
9.3. Bridges
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 







9-2-6-otsoedinenie-i-podsoedinenie-kardannykh-valov-na-razdatochnojj-korobke.html

9.2.6. A detachment and connection of driveshafts on a transfer case

Details of installation of a transfer case (on a series 750.653 example)

1 — the Transfer case
2 — the Lever переключения*
3 — Pylnik*
4, 16, 18 — Driveshafts
5, 15 — Screws
6 — the Washer
7 — Rubber pillows
8, 12 — Sealing rings
9 — the Stopper of a jellied opening
10 — Angular привод*
11 — a drive Shaft спидометра*

13 — the Drain stopper
14 — the Basic lever
17, 19, 25 — Nuts
20 — the Hollow bolt of shtutserny connection
21 — Sealing washers
22 — the Line of a pneumatic path
23 — the Socket
24 — the pumping Line
S76/7 — the Sensor switch of the indicator of blocking of interaxal differential

* On considered models is absent

Detachment

Target shaft of a drive of the forward bridge

 PERFORMANCE ORDER

  1. Transfer the AT selector lever to the situation "N", a transfer case include in a movement mode on the road.
  2. Поддомкратив the car, hang out the left forward wheel.
  3. Rotating the hung-out wheel, отболтите the driveshaft (18), take him aside and tie up.

Shaft of a drive of a transfer case

 PERFORMANCE ORDER

  1. Transfer AT and a transfer case to neutral provisions.
  2. Rotating a power shaft (16), отболтите it, take him aside and tie up.

Target shaft of a drive of the back bridge

 PERFORMANCE ORDER

  1. Transfer the AT selector lever to the situation "N", a transfer case include in a movement mode on the road.
  2. Поддомкратив the car, hang out the left back wheel.
  3. Rotating the hung-out wheel, отболтите the driveshaft (4), take him aside and tie up.

Connection

Nuts of fastening of driveshafts are subject to replacement without fail!


 PERFORMANCE ORDER

  1. Develop an entrance flange on a transfer case a yellow label down.
  2. Having developed driveshafts green labels up, connect them to the flanges on a transfer case.
  3. Track, that NEW fixing nuts were tightened with demanded effort.


«previous page
9.2.5. Removal and installation of the servomotor of a transfer case
following page»
9.2.7. Removal and installation of a transfer case