Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
13.1. General information
13.2. Assembly blocks and management modules
13.3. Switches
13.3.1. Removal and installation of switches of a steering column
13.3.2. Group of switches at the left on the dashboard
13.3.3. Removal and installation of the handle of the switch and actuation mechanisms of a drive of correction of provision of block headlights
13.3.4. Removal and installation of assembly of the top groups of switches of a console part of the dashboard
13.3.5. Removal and installation of the panel of switches of blocking of differentials
13.3.6. Removal and installation of the panel of switches of the electric drive of window regulators of a driver's door
13.3.7. Removal and installation of the panel of the ceiling console
13.3.8. Removal and installation of a combination of devices
13.4. Driving electromotors, sensors
13.5. Alarm and lighting devices
13.6. Systems of additional safety (SRS)
13.7. Audiosystem, navigation and mobile phone
14. Schemes of electric connections


 









13-3-3-snyatie-i-ustanovka-rukoyatki-pereklyuchatelya-i-ispolnitelnykh-ustrojjstv.html

13.3.3. Removal and installation of the handle of the switch and actuation mechanisms of a drive of correction of provision of block headlights

Details of installation of the handle of a drive of adjustment of an inclination of optical axes of headlights

1 — the switch Handle
2 — the Assembly bracket
3 — the Remote plug

4 — the plug Through passage
8 — the Opening in a partition

Details of installation of the actuation mechanism of a regulator of an inclination of optical axes of headlights

5 — the Pilot line
6, 7 — Bandage clamps

9 — the Actuation mechanism
10 — the Cover

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding

  1. Turn the handle (1) drive of the hydroproof-reader in situation "0" and, without rotating, remove it from the dashboard.
  2. Remove the left bottom section of furnish of the dashboard (see. Head Body).
  3. Remove an assembly bracket (2).
  4. Remove the left group of switches of the dashboard (see. The section Group of switches at the left on the dashboard).
  5. Remove a face cover of a steering column (see. Head Body).
  6. Remove the remote plug (3).
  7. Remove a forward decorative lattice (see. Head Body).
  8. Remove a block headlight (see. Section Removal and installation of block headlights, replacement of lamps, adjustment of the direction of optical axes).
  9. Remove a front bumper (see. Head Body).
  10. Remove a loker of protection of a wheel arch (see. Head Body).
  11. Turn out forward fixing screws and uncover (10) and the rubber sealant established under it.
  12. Remove assembly of the vacuum amplifier of brakes (see. Head Brake and auxiliary systems).
  13. Open the plug (4) through passage and take from it a sealant from porous rubber. Having pulled forward, remove the plug (4).
  14. On models 463/323 remove the tank of liquid of washing of glasses (see. Head Body).
  15. Release bandages (6 and 7) and separate a pilot line (5) from the panel of a wheel arch and a cross-section beam of a radiator, - bandages are subject to replacement without fail.
  16. Push the actuation mechanism of a regulator (9) in a window in the panel of a front and remove it from the car, having carried out through openings in a partition (8) and a wheel arch and having liberated from the plug (4) through passage, - try not to bend hydraulic lines!
  17. Installation is made upside-down, - on models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  18. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).
  19. Check correctness of adjustment of an inclination of optical axes of headlights, in case of need make the corresponding adjustment (see. Specifications).


«previous page
13.3.2. Group of switches at the left on the dashboard
following page»
13.3.4. Removal and installation of assembly of the top groups of switches of a console part of the dashboard