Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
13.1. General information
13.2. Assembly blocks and management modules
13.3. Switches
13.4. Driving electromotors, sensors
13.4.1. Removal and installation of electromotors of a drive of screen wipers
13.4.2. Removal and installation of activators of the uniform lock
13.4.3. Removal and installation of electromotors of a drive of adjustment of forward seats
13.4.4. Removal and installation of sensors
13.5. Alarm and lighting devices
13.6. Systems of additional safety (SRS)
13.7. Audiosystem, navigation and mobile phone
14. Schemes of electric connections


 







13-4-privodnye-ehlektromotory-datchiki.html

13.4. Driving electromotors, sensors

Removal and installation of electromotors of a drive of screen wipers

Forward screen wipers

Details of installation of the electromotor of a drive of cleaners of a windscreen

1 — the Assembly bracket
2 — the Tank
3 — the Cover of the driving electromotor
4 — the Refrigerator line
5 — Draught of a drive of screen wipers
6 — the Driving crank
M6/1 — the Driving electromotor
S62 — the Sensor switch of a cowl of ATA system

Y68 — the Longitudinal balance weight Ý/m the valve of blocking of differential
Y68/1 — Ø/m the valve of blocking of back differential
Y68/2 — Ø/m the valve of blocking of forward differential
Shooters — Reference points

 PERFORMANCE ORDER

  1. Take a key from the lock of ignition and disconnect a negative wire from the battery.
  2. Remove from support and lower down electromagnetic valves of blocking of differentials (Y68, Y68/1 and Y68/2), - try not to damage vacuum lines.

Before a detachment of electroconducting and vacuum lines do not forget to put the corresponding marking guaranteeing correctness of their connection at assembly.

  1. Remove from an assembly bracket (1) tank (2) and, without overturning, lower it down, - try not to spill brake liquid.
  2. Disconnect electroconducting from the sensor switch (S62) of a cowl of anticreeping system (ATA).
  3. Turn out screws (shooters) of fastening of a clamp of ventilating lines on an assembly bracket. Get ventilating lines under refrigerator (4) and, having lowered, take them aside. Remove an assembly bracket (1).
  4. Uncover (3) electromotors (M6/1) of a drive of screen wipers.
  5. Disconnect electroconducting, turn out fixture (shooters) and remove the electromotor (M6/1) from support (arrow).
  6. Having submitted the electromotor (M6/1) forward, operating through a window in a partition, hook and separate from a crank (6) driving draft (5), - try not to bend draft.
  7. Finally remove the electromotor (M6/1).
  8. Installation is made upside-down.
  9. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. The head of System of electric equipment of the engine) also execute procedures of base programming.

Back screen wiper

Details of installation of the electromotor of a drive of a cleaner of back glass

1 — the Cover
2 — the Nut
3 — the Bolt

M6/4 — the Driving electromotor
M6/4x1 — I Will corrode electroconductings

 PERFORMANCE ORDER

  1. Dismantle a back screen wiper (see. Head Body).
  2. Uncover (1).
  3. Having released clamps and, without inclining, remove the central section of the top panel of furnish of a door of a back.
  4. Disunite the socket (M6/4x1) of electroconducting of the driving motor (M6/4).
  5. Turn out fixing bolts (3) and remove the electromotor (M6/4).
  6. Installation is made upside-down.


«previous page
13.3.8. Removal and installation of a combination of devices
following page»
13.4.1. Removal and installation of electromotors of a drive of screen wipers