Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
13.1. General information
13.2. Assembly blocks and management modules
13.3. Switches
13.4. Driving electromotors, sensors
13.5. Alarm and lighting devices
13.5.1. Removal and installation of block headlights, replacement of lamps, adjustment of the direction of optical axes
13.5.2. Removal and installation of the back combined lamps
13.5.3. Removal and installation of indexes of turns
13.5.4. Removal and installation of a stoplight of the top level
13.5.5. Removal and installation of fog lights
13.5.6. Replacement of lamps of internal lighting
13.6. Systems of additional safety (SRS)
13.7. Audiosystem, navigation and mobile phone
14. Schemes of electric connections


 









13-5-signalnye-i-osvetitelnye-pribory.html

13.5. Alarm and lighting devices

Removal and installation of block headlights, replacement of lamps, adjustment of the direction of optical axes

Removal and installation

Details of installation of a block headlight

1 — the Bolt
2, 3 — electroconducting Sockets
3 — Nuts
4 — the Adjusting screw

5 — the Regulator
6 — the Basic arm
Е1 — the Left block headlight
Е2 — the Right block headlight

 PERFORMANCE ORDER

  1. Uncover block headlights (see. Head Body).
  2. Turn out a bolt (2) and remove block headlights (E1/E2).
  3. Disunite the socket (2) electroconductings of a passing/driving beam.
  4. Disunite the socket (3) electroconductings of marker/parking lights.
  5. Completely turn out the adjusting screw (4) regulators (5) provisions of a block headlight, develop a regulator to the left and remove from a basic arm (6), - try not to allow peregibaniye of the hydraulic line.
  6. Installation is made upside-down.
  7. In summary check correctness of installation of optical axes of headlights, in case of need make the corresponding adjustment (see below).

Replacement of lamps

Replacement of lamps of a block headlight

1 — the Spring clamp
2 — the Lamp of a passing/driving beam

3 — the Lamp of marker/parking light

 PERFORMANCE ORDER

  1. Remove a block headlight (see above).
  2. Remove a rubber back cover.
  3. Release a spring clamp and take from directing a lamp of a passing/driving beam (2), - try not to touch a lamp flask barehanded.
  4. Having pulled, liberate from a reflector a lamp of marker/parking light (3), - also try not to touch a flask barehanded.
  5. Installation is made upside-down.

Adjustment of an inclination of optical axes of headlights

Adjustment is made on not loaded car with a busy driver's seat (cargo in mass of 75 kg).

Adjustment of an inclination of optical axes of headlights is made by means of a test board

10 — Distance in meters
е — an adjustment Range (see. Specifications)
N — Height of position of the center of a block headlight

h — Height of position of the line of a cut of a working zone of a board
S — the Block headlight

Example of illumination of a working zone of a test board

Location of adjusting screws

1 — Adjustment in the vertical plane

2 — Adjustment in the horizontal plane

 PERFORMANCE ORDER

  1. Check correctness of a rating of tires (demanded values are specified on inside of a cover of the hatch of a jellied mouth of a fuel tank).
  2. Remove external covers (a facing framework) block headlights (see. Section Removal and installation of covers of block headlights).
  3. Establish the handle of the switch of the hydroproof-reader of headlights at the left on the dashboard in situation "0".
  4. Check should be made in the conditions of a car-care center workshop with application of the special test board established at distance of 10 meters ahead of a checked headlight strictly according to instructions of manufacturers.
  5. Adjustment is considered correct if the line of a cut of the light spot generated by included in a mode of a passing beam of a headlight it is combined with a horizontal marking (the cut line) working zone of a board to the left of its center. In case of need make the corresponding adjustment by means of vertical (1) and horizontal (2) regulators.


«previous page
13.4.4. Removal and installation of sensors
following page»
13.5.1. Removal and installation of block headlights, replacement of lamps, adjustment of the direction of optical axes