Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
8.1. Specifications
8.2. Search of malfunctions - the general information
8.3. The general principles of functioning of a control system of the transmission, operating signals
8.4. Adjustment of a drive of switching of AT
8.5. Removal and installation of the electrohydraulic control unit by switchings
8.6. Removal and AT installation with the hydrotransformer
8.7. Removal and installation of the selector module (ESM)
8.8. Removal and installation of the sensor of target turns of AT
8.9. Removal and installation of a cooler of ATF
8.10. Washing of a cooler of ATF and oil pipelines
8.11. Removal and installation of the electronic module of management by transmission (TCM/ETC)
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
14. Schemes of electric connections


 









8-6-snyatie-i-ustanovka-at-s-gidrotransformatorom.html

8.6. Removal and AT installation with the hydrotransformer

AT installation details

1 — Carter AT
2 — the Jellied tube
3 — Oil pipelines
4 — the grounding Tyre on weight
5 — the Driveshaft
6 — the Back support of a suspension bracket of the power unit
7 — Draught of switching

8 — the Hollow bolt of shtutserny connection
9 — the Drain stopper of the pallet of a case of AT
10 — the Arm
11, 12 — Covers
13 — Bolts (external TORX)
14 — the Fixing collar
В49 — the Sensor of target turns of AT
X22/2 — I Will corrode AT electroconductings

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. To Poddomkratta the car also establish it on props.
  4. Disconnect from engine and transmission cases a jellied tube (2).
  5. Turn out a stopper (9) and merge transmission liquid, - at once estimate ATF condition, in case of need make its replacement (see. Head Current leaving and service).
  6. Release bandages, separate an electroconducting plait from a jellied tube and disunite the contact socket (X22/2), - prepare replaceable bandages.
  7. Turn out the sensor of target turns of transmission (В49), - in case of need prepare a replaceable sealing ring.
  8. Unscrew the left and right oil pipelines going to a maslookhladitel.
  9. Release a fixing collar and remove draft of switching (7).
  10. Uncover (12) and disconnect the hydrotransformer from a driving disk.
  11. Prop up transmission by a special jack.
  12. Remove a cross-section beam assembled with a back support of a suspension bracket of the power unit (6).
  13. To Otboltita the driveshaft (5) from a target flange of transmission and a transfer case also take from under the car, - in case of need previously отболтите and incline transmission (see below), - and tie up it to bottom elements.
  14. Remove the stabilizer of cross-section stability (see. Head Suspension bracket and steering).
  15. Release a fastening bandage to a frame of a plait of the electroconducting laid to the left of transmission.
  16. To Otboltita tire of grounding (4).
  17. Turn out bolts of fastening of AT to the engine and lower it at an angle, - if yet did not do it, remove the driveshaft.
  18. In case of need by means of special strippers take from transmission the hydrotransformer.
  19. Installation is made upside-down, - before installation it is necessary to grease a driving flange of the hydrotransformer slightly. Track correctness of installation of the driveshaft.
  20. In summary деактивируйте a service mode of TELE AID system also make cleaning of memory of the processor of system of onboard self-diagnostics (see. Head of System of electric equipment of the engine).


«previous page
8.5. Removal and installation of the electrohydraulic control unit by switchings
following page»
8.7. Removal and installation of the selector module (ESM)