Mercedes-Benz G-class (W463) since 1999 of release
1. Introduction
2. Governing bodies and operation receptions
3. Current leaving and service
4. Engine
5. Systems of cooling, heating, ventilation and air conditioning
6. A power supply system and production of the fulfilled gases
7. Systems of electric equipment of the engine
8. Automatic transmission
9. Transmission line
10. Brake and auxiliary systems
11. Suspension bracket and steering
12. Body
13. Onboard electric equipment
13.1. General information
13.2. Assembly blocks and management modules
13.2.1. Detachment and connection of electroconducting of assembly blocks and management modules
13.2.2. Removal and installation of assembly blocks of safety locks and relay
13.2.3. Removal and installation of modules of management
13.3. Switches
13.4. Driving electromotors, sensors
13.5. Alarm and lighting devices
13.6. Systems of additional safety (SRS)
13.7. Audiosystem, navigation and mobile phone
14. Schemes of electric connections


 


13-2-3-snyatie-i-ustanovka-modulejj-upravleniya.html

13.2.3. Removal and installation of modules of management

General information

The scheme of an arrangement of modules of management onboard the car

A2/5 — the Antenna divider
A2/6 — a CD changer
A2/22 — the Aerial
A2/42 — the TV tuner
A2/65 — the Antenna amplifier
A35/8 — the Module of management of system of an emergency call (E-call) of TELE AID
A35/11 — the Module of management of Linguatronic system
В33 — the Sensor of an inclination of anticreeping system (ATA)
В66 — Konusny the inclination sensor
N2/2 — the Module of management of SRS
N3/10 — the Module of management of ME-SFI injection
N10/1 — the Right module of management of SAM/assembly the block
N10/2 — the Back module of management of SAM/assembly the block

N15/3 — the Module of management of AT (TCM/ETC)
N15/5 — the Selector module (ESM) of AT
N15/7 — the Module of management of a transfer case of VGS
N25/6 — the Module of management of heating of back seats
N27 — the Module of management of the sensor of protection against towage
N28/1 — the Module of management of system of registration of connection of the trailer
N39/2 — the Module of management of injection of CDI
N47-7 — the Module of management of ABS
N62 — the Module of management of system of the help at movement by a backing (BA)
X4/30 — the Terminal block (a contour 30, the engine)
Y58/1 — the Valve of a purge of a coal adsorber

The description of procedures of removal and installation of modules of management by injection (ME-SFI/CDI), AT (TCM/ETC), transfer case, brake and auxiliary stabilization systems (ABS/BAS/EBV/ESP) is provided in the corresponding Heads of the Management (see. Heads of the Power supply system and production of the fulfilled gases, Automatic transmission, the Transmission line and the Suspension bracket and a steering).

The module of management of COMAND system with the multipurpose display (ET4 code)

Details of installation of the module of management of COMAND with the multipurpose display (1 of 2)

1 — the Bolt
A40/3 — the Module of management of teams with the multipurpose display

Details of installation of the module of management of COMAND with the multipurpose display (2 of 2)

1 — the Socket of a signal of the RGB TV tuner
2 — I Will corrode tires CAN (to a combination of devices)
And — I Will corrode food giving
In — the loudspeaker Socket
D2B — the Socket of the fiber-optical tire

D — the Socket of an entrance signal of the FM/AM aerial
Е — the Socket of an entrance signal of GPS
F — the Socket of a target signal of IF*
S — the Safety lock

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove facing of the central section of the dashboard (see. Removal and installation of the facing panel of console section of the dashboard).
  4. Turn out fixing bolts (1) and liberate assembly of the module of management / the multipurpose display (A40/3) from the dashboard.
  5. Disunite electric sockets (1, 2, And, In, D, Е, F).
  6. Accurately, trying not to extend and not to break a cable, disunite the D2B socket of the fiber-optical tire.
  7. Installation is made upside-down, - at the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  8. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).

Modules of management of door assemblies

Forward door

Details of installation of the module of management of a forward door

In — Fixing screws
With — Bindings

N69/1 — the Module of management of the left door
N69/2 — the Module of management of the right door

 PERFORMANCE ORDER

  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding
  1. Remove the panel of an internal upholstery of a door (see. Head Body).
  2. Disconnect electroconducting from the door module of management (N69/1 or N69/2) (see. Section Detachment and connection of electroconducting of assembly blocks and management modules).
  3. Turn out fixing screws (In) and remove the management module (N69/1 or N69/2).
  4. Installation is made upside-down, - electroconducting of modules, having tracked that wires did not cross, fix new bandages (C).
  5. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).

Back door

Details of installation of the module of management of a back door (1 of 2)

1 — Clamps
2 — Latches
3 — the upholstery Panel

N69/3 — the Module of management of the left door
N69/4 — the Module of management of the right door

Details of installation of the module of management of a back door (2 of 2)

And — the Binding


 PERFORMANCE ORDER

  1. Turn on the auxiliary accumulator and connect it to the regular battery then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding

  1. Remove the panel of an internal upholstery of a door (3) (see. Head Body).
  2. Disconnect electroconducting from the door module of management (N69/3 or N69/4) (see. Section Detachment and connection of electroconducting of assembly blocks and management modules).
  3. Having compressed clamps (1), remove the management module (N69/3 or N69/4).
  4. Installation is made upside-down, - electroconducting of modules, having tracked that wires did not cross, fix a new binding (And).
  5. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).

Modules of management of system of activation and perception of a signal (SAM) / assembly blocks of safety locks and relay

Forward module

Details of installation of the forward SAM/assembly module of the block of safety locks and relay

1, 2 — Nuts
3, 4 — I Will corrode SAM electroconductings

N10/1 — the Forward module of management of SAM

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the main ware box (see. Head Body).
  4. Remove the right bottom cover of the dashboard (see. Head Body).
  5. Give fixing nuts (1 and 2) and remove the forward SAM/assembly module the block (N10/1).
  6. Previously having marked, disunite sockets (3 and 4) the module of management (N10/1) (see. Section Detachment and connection of electroconducting of assembly blocks and management modules).
  7. Installation is made upside-down, - track correctness of laying of electroconducting and reliability of fixing of its sockets (see. Section Detachment and connection of electroconducting of assembly blocks and management modules).
  8. On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  9. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. The head of System of electric equipment of the engine) also enter demanded base settings of the onboard equipment.

Back module

Details of installation of the back SAM/assembly module of the block of safety locks and relay (N10/2)

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the central console (see. Head the Body) and the air line laid under it.
  4. Turn out fixing screws and remove the SAM/assembly module the block (N10/2).
  5. Installation is made upside-down, - track correctness of laying of electroconducting and reliability of fixing of its sockets (see. Section Detachment and connection of electroconducting of assembly blocks and management modules).
  6. On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  7. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. The head of System of electric equipment of the engine) also enter demanded base settings of the onboard equipment.

Module of management of the electronic switch of ignition (EIS/EZS)

Details of installation of the module of management of EIS/EZS

1 — Clamps
2 — the Driving cable of the lock of ignition

3 — I Will corrode electroconductings
N73 — the Module of management of EIS/EZS

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).

  1. Turn on the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding

  1. Take the ignition key.
  2. Remove the left bottom section of furnish of the dashboard (see. Head Body).
  3. Compress clamps (1) and disconnect from the EIS module (N73) a driving cable (2), having pulled it in the direction specified by an arrow.
  4. Disunite the socket (3) electroconductings of the EIS module (N73).
  5. Installation is made upside-down, - the replaceable EIS module should be programmed according to instructions enclosed in a set.
  6. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).

Module of management of telecommunications (ET7/EV7 codes)

Details of installation of the module of management of telecommunications (ET7/EV7 codes)

1 — the module Console
And — I Will corrode connections of a fiber-optical cable

In — the Socket
N112 — the management Module

 PERFORMANCE ORDER

  1. Remove the central console (see. Head Body).
  2. Disunite the socket (And) connections of a fiber-optical cable on the module of management (N112), - at once close sockets of wave guides protective caps.
  3. Having compressed lock uvulas and having accurately pulled, disunite the socket (In).
  4. Turn out 2 fixing screws and having released one nut, remove the console (1) module of management (N112) from the tunnel of the transmission line.
  5. Turn out two fixing screws located from below and remove the module of management (N112) from the console panel (1).
  6. Installation is made upside-down.
  7. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. Head of System of electric equipment of the engine).

Module of management of system of an emergency call TELE AID (ET2 code)

Models 463.250/323/333

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.250/323/333

1 — Screws
2 — electroconducting Sockets

A35/8 — the management Module
The shooter — I Will corrode electroconductings

 PERFORMANCE ORDER

  1. On models of the corresponding complete set (ET2 code) activate a service mode of system of an emergency call of TELE AID (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  2. Disconnect a negative wire from the battery.
  3. Remove the central console (see. Head Body).
  4. Remove the module of management of AT (ECM/ETC) (see. Head Automatic transmission).
  5. Turn out three fixing screws (1), disunite two sockets (2), then disunite the socket shown by an arrow, and remove the management module (A35/8).
  6. Replace the independent battery of a food of system of an emergency call.
  7. Installation is made upside-down.
  8. On models of the corresponding complete set (ET2 code) деактивируйте a service mode of TELE AID system (see. Section Activation/deactivation of a service mode of system of an emergency call of TELE AID).
  9. In summary make reading of the DTC codes and cleaning of memory of system of onboard self-diagnostics by means of the STAR DIAGNOSIS scanner (6511 1801 00) (see. The head of System of electric equipment of the engine) also enter demanded base settings of the onboard equipment.

Models 463.246/249

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.246/249 (1 of 3)

1 — the Cover of the module of management
3 — the Fixing nut
A35/8 — the management Module
A35/8j10 — I Will corrode electroconductings

In — I Will corrode electroconductings of the tire of data of CAN
With — the Socket of an antenna cable
Arrow — Clamps

Details of installation of the module of management of system of an emergency call of TELE AID on models 463.246/249 (2 of 3)

4 — the Fixing nut
5 — the module Console

6 — Fixing nuts

Details of installation of the console of the module of management of system of an emergency call of TELE AID on models 463.246/249 (3 of 3)

5 — the module Console
7 — Fixing nuts

8 — the Wire of the tire of data of CAN
9 — the Porous insulating material

 PERFORMANCE ORDER

  1. Lift the right forward seat and shift it back against the stop.
  2. Release two clamps (2) fastenings of the forward party of a cover (1) module of management.
  3. Shift the lifted seat against the stop forward, release two back clamps (arrow) and uncover (1).
  4. Give two nuts (3) fastenings of a back part of the module of management (A35/8).
  5. Again take away the lifted seat in extreme back situation, give two forward nuts (4) and remove the module (A35/8).

  1. Switch off ignition, activate the auxiliary accumulator and connect it to the regular battery, then disconnect from the last a negative wire.

    7 — the Auxiliary accumulator
    8 — the Plug of a positive wire of the module
    9 — the Plug of a negative wire of the module
    W10 — battery Grounding

  1. Remove the management module (A35/8) from a basic arm.
  2. Unblock and disunite the socket (A35/8j10).
  3. Disconnect a fiber-optical cable of the tire of data of CAN and at once muffle both halves of its socket (In) special, preventing light influence, protective caps.
  4. Disunite the socket (C) an antenna cable.
  5. Remove the module of management of system of an emergency call of TELE AID (A35/8).
  6. In case of need release lobbies (6) and back (7) nuts, separate from the console (5) a wire (8) tires CAN, release from a penoizolyatsionny material (9) and disunite contact sockets, - take care of protection of a fiber-optical wave g