|
2-4-1-avtomatizirovannaya-sistema-kondicionirovaniya-vozdukha-termatic.html
2.4.1. Automated central air of air (Termatic)Automated central air of air (Termatic)
The control panel functioning of the automated To/in system
The design of the control panel of To/in system is presented on an illustration.
Control panel Termatic system functioning
Termatic system activation/deactivation
For activation of system it is necessary to deduce a rotary regulator of a choice of a high-speed mode of the fan from situation 0. Return of a regulator to zero situation allows to disconnect system.
|
|
At the disconnected system the supply and circulation of salonny air also stop that can lead to a fast zapotevaniye of glasses, - try at using the car not to disconnect system for a long time! |
Mode of automatic functioning
The AUTO mode when the choice of intensity and the direction of distribution of air is carried out by system automatically proceeding from the temperature installations set by the user, is base. For activation of a mode press the AUTO button on control panels, - the control light-emitting diode built in the button should light up. The choice of a demanded temperature mode in the right or left part of salon is carried out by rotation of the corresponding rotary regulator, - try to make correction of temperature modes by small steps.
|
|
Activation of electroheating of back glass can be made in case of need manually. |
Manual adjustment of intensity and directions of distribution of air
Intensity and the direction of distribution of air can be exposed manually by means of lateral rotary regulators on the control panel after preliminary shutdown of an automatic mode from the corresponding button, - the built-in control light-emitting diode of the AUTO mode should go out, - chosen earlier temperature installations will change. Intensity of supply of air can change within 5 steps of high-speed modes of functioning of the fan.
|
|
At installation of intensity of supply of air on a zero Termatic system shutdown is made! The choice of this installation should be made only for short time. |
The choice of the direction of distribution of air provides the following possible options:
Supply of air on having blown wind and lateral glasses
Supply of air on having blown in glasses, on obverse level and in foot wells
Supply of air in lobbies and back foot wells
Supply of air on obverse level Return to an automatic mode can be made by repeated pressing the AUTO button, - make sure of serviceability of activation of a control light-emitting diode. Mode of removal of condensate from glasses
For fast removal of condensate from glasses press the button, - the control light-emitting diode built in in the button should light up. Thus the system automatically provides transfer to the maximum productivity of a heater and the fan, and all stream of air submitted to salon will be redirected on having blown wind and lateral glasses with shutdown of its giving in a back part of salon. At the corresponding complete set windscreen electroheating is automatically activated. Adjustment of all other installations, except for function of electroheating of back glass, for the period of activation of a mode is blocked.
|
|
The heating element of heating of a windscreen consumes a lot of electric power therefore it is not necessary to activate it for a long time, - heating shutdown on the timer is not provided! |
For mode shutdown rather repeatedly to press the same button, or on the AUTO button.
|
|
For condensate removal from an external surface of a windscreen it is necessary to choose a mode of supply of air on having blown in glasses () and to activate screen wipers. |
Air circulation mode
Activation of a mode of air circulation is made by means of the button
on the To/in control panel, - the control light-emitting diode built in the button should light up. In this mode giving shutdown in salon of fresh air that allows to prevent penetration into salon of exhaust gases and unpleasant smells is made.
|
|
Long use of a mode of circulation, leads to a zapotevaniye of glasses and increase of a spertost of air therefore it is recommended to activate this mode only in case of the valid need and for rather short time, for example, at movement on the district with the filled with smoke or zagazovanny atmosphere. As soon as need of isolation of salon disappears, supply of fresh air should be renewed. |
The repeated pressing the button of the switch allows to restore supply of air. Also automatic shutdown of a mode of circulation on a timer signal is provided: approximately in 30 minutes at temperature of external air from 5 and above, or in 5 minutes at temperature of external air is lower 5. Five-minute installation is activated also at the chosen economic mode of functioning of system (see below).
|
|
At high temperatures of external air 30-minute activation of a mode of circulation can automatically be made and is not accompanied by inclusion of a control light-emitting diode of the push-button switch. |
Economic mode
At a choice of an economic mode / compressor shutdown is made. For activation of a mode press the ACoff/REST button on control panels, - the control light-emitting diode built in in the button should light up.
|
|
On models of the corresponding complete set also automatic shutdown of an additional heater is made. |
In an economic mode such functions of Termatic system, as cooling and air drainage are disconnected. Shutdown of a mode is made by repeated pressing of the same button. Mode of use of residual heat of the engine
Heating of salon can be made during even some time after an engine stop at the expense of use of the power unit of residual heat accumulated in the mass. Activation of a mode is made by means of the ACoff/REST button on the control panel, - the control light-emitting diode built in the button should light up. Before inclusion of a mode of use of residual heat of the engine (REST) turn a key in the ignition lock in situation 1.
At the activated mode adjustment of intensity and the directions of supply of air is made automatically (the minimum high-speed mode of the fan usually gets out). Duration of functioning of system depends on the chosen temperature installations and reference temperature of cooling liquid of the engine.
|
|
Necessary condition of use of the REST mode is sufficient level of a charge of the storage battery. |
Switching off of a mode is made automatically on a timer signal approximately in 30 minutes, at a key povorachivaniye in the ignition lock in situation 2, and also at appreciable decrease in level of a charge of the storage battery. Heating of back glass
Heating of back glass functions only in situation 2 keys in the ignition lock. Activation of a heating element of back glass is made by means of the corresponding button on the system control panel, - the control light-emitting diode built in the button should light up.
|
|
In a winter season before inclusion of heating remove from glass and snow. |
|
|
The heating element of heating of back glass consumes a lot of electric power therefore it is not necessary to activate it for a long time. |
Automatic shutdown of heating is made on a timer signal approximately in 6-17 minutes, depending on temperature of external air and speed of movement of the car.
|
|
Shutdown of heating of back glass can occur also at simultaneous activation of a large number of consumers of the electric power, and also at appreciable decrease in level of a charge of the storage battery, - the control light-emitting diode built in the button will start to blink. With restoration of level of tension the heating element is activated automatically. |
| |